Looking for H803 Dual Display Kit XL?
<aside> ⚠️ You are about to load the structure with additional weight. Before proceeding check the structure for a proper installation. Check the anchor screws. Check for a level structure.
</aside>
Temporarily install each dual display bar to the main structure by sliding the post on the back of the bar into the vertical slot located at the top corners of the structure.
<aside> 💡 When properly installed, the bar’s weight will rest on the peak of the leg of the structure.
</aside>
Install the safety pins to connect each bar to the beam of the structure. Install two pins to each bar.
<aside> 💡 While this is a temporary installation of the dual display bars, it is good practice to immediately install the safety pins to ensure the bars do not move unexpectedly.
</aside>
Fasten the display-alignment screws through each dual display bar. Adjust each screw with the included ball-end hex key until both dual display bars are level.
Locate the wall stud, near the far end of each dual display bar, that aligns with a pill-shaped anchor hole on each dual display bar.
Mark the pill-shaped hole on the wall. Do this near the end of both dual display bars.
<aside> 💡 Before you remove the dual display bars to drill the wall anchor holes, use this opportunity to relocate the display-locking bumpers to the correct location for your display.
</aside>
<aside> ⚠️ Before you remove the dual display bars to drill the wall anchor holes, use this opportunity to relocate the display-locking bumpers to the correct location for your display.
</aside>
Two display-locking bumpers are pre-installed to each dual display bar. The
Measure the horizontal distance from the edge of the display to the nearest mounting hole.
<aside> 🗒️ Take note of this Distance A.
</aside>
Measure the horizontal distance from the edge of the display to the farthest mounting hole.
<aside> 🗒️ Take note of this Distance B.
</aside>
Locate the correct hole on the dual bar to install the inner display-locking bumper. To do so, measure Distance A from the center of the structure (marked with a triangular notch) to the row of bumper-mounting holes on the dual-display bar. Mark the hole that is just short of Distance A with tape.
Locate the correct hole on the dual bar to install the outer display-locking bumper. To do so, measure Distance B from the center of the structure (marked with a triangular notch) to the row of bumper-mounting holes on the dual-display bar. Mark the hole that is just short of Distance B with tape.
Repeat this process to locate the bumper positions on the other dual display bar.
<aside> 💡 It is easier to install the display-locking bumpers when the dual-display bars are removed from the structure.
</aside>
Remove the dual display bars from the structure by removing the adjustment screws and safety pins and lifting the bars from the structure.
Relocate the bumpers from their pre-installed location to your marked locations.
<aside> 💡 When in doubt, install each bumper one hole closer towards the center of the structure. This will still enable the display rails to clasp the bumper without stopping each display from sliding to reach the center of the structure.
</aside>
<aside> ⚠️ High-voltage wires may be present inside the wall. There is a risk of injury or death by electric shock. Shut off power to the area at the circuit breakers before proceeding.
</aside>
<aside> 💡 The included wall anchors are designed to anchor to steel studs. For anchoring to wood studs, please source hardware appropriate to anchoring to wood studs. For wood studs, we recommend using ⅜ inch diameter Hex Head Screws.
</aside>
Drill a ¾-inch diameter hole within the pill-shape mark traced to your wall. Drill the hole towards the lower end of the pill shape. Drill through the drywall and the steel wall stud.
Install the SnapToggle wall anchor into the wall and wall stud.
Repeat for the wall anchor location for both dual display bars.
Reinstall the dual display bar to the main structure.
Install the safety pins.
<aside> ⚠️ For redundant safety, install two safety pins into each dual display bar.
</aside>
Fasten the adjustment screw connecting the dual display bar to the horizontal beam.
Adjust the screw to level the dual display bar.
Fasten the dual display bar to its wall anchor using the provided screw, washer, and shouldered nylon spacer.
<aside> 💡 When fastened, the dual bar will be anchored to the wall but free to move up and down slightly to enable alignment of two displays in later steps.
</aside>
Repeat steps for the second dual display bar.
<aside> 🗒️ How far above the finished floor (AFF) do you want the bottom edge of your displays? Take into account several factors such as the desired position of the video camera lens, display size, and a comfortable screen viewing angle. In general, we recommend positioning the center of your camera lens about 44 inches to 46 inches AFF. Then position the bottom edge of your display about one inch above the body of the camera.
</aside>
<aside> 💡 Consider if camera movement will cause the camera to strike the display. For example, the hibernation position of a Logitech Rally Camera requires two additional inches of clearance between the display and the camera.
</aside>
Place masking tape on the wall at the height where you would like to position the bottom edge of your display.
Measure the distance between the tape and the top edge of the dual display bar.